How to Make a Beautiful Epoxy Resin Table with Scarlet Roses

Introduction

Epoxy resin art is a creative way to transform simple materials into beautiful and unique home décor. In this DIY project, we will learn how to create a stunning 40 cm epoxy resin table decorated with scarlet roses and decorative beads.

The combination of black resin, vibrant red roses, and beads of different sizes creates an elegant design. By pouring multiple layers of resin, sanding the surface, and applying a final glossy coating, you can create a beautiful decorative table for your home.

In this step-by-step tutorial, we will explain the materials required and the complete process of making this floral epoxy resin table.

Materials Required

Before starting the project, gather the following materials:

  • 40 cm silicone mould

  • Epoxy resin and compatible hardener

  • Black pigment paste

  • Scarlet roses, properly dried for resin casting

  • Decorative beads of different sizes

  • Measuring cups and mixing sticks

  • Protective gloves, goggles, and suitable work clothing

  • Bubble-removal spray compatible with your resin

  • 40-grit and 80-grit sandpaper

  • Sanding machine

  • Dust-removal equipment

  • Drill and mounting hardware

  • Table base

  • UV resin, if suitable for the mounting application

Step-by-Step Process to Make an Epoxy Resin Table

Step 1: Prepare the Silicone Mould

Start by preparing a 40 cm silicone mould. Place it on a clean, flat, and level surface to ensure that the resin spreads evenly.

Wear appropriate protective equipment before handling the resin. Work in a well-ventilated area and follow the manufacturer's safety instructions.

Step 2: Prepare the First Layer of Epoxy Resin

For the first layer, measure the following ingredients:

  • 300 g epoxy resin

  • 150 g hardener

  • Black pigment paste

Mix the resin and hardener thoroughly according to the manufacturer's specified ratio. Scrape the sides and bottom of the container to ensure that both components are properly combined.

Add the black pigment paste and mix until the colour becomes uniform.

Step 3: Pour the Resin into the Mould

Slowly pour the black resin mixture into the silicone mould. Spread it evenly until the intended surface is completely covered.

Pour carefully to minimize the formation of air bubbles and ensure an even base layer.

Step 4: Arrange the Scarlet Roses and Decorative Beads

Now comes the most creative part of the project.

Carefully arrange the scarlet roses on the resin surface. Add decorative beads of different sizes to create an attractive floral composition.

Take your time to position the flowers and beads according to your preferred design. The contrast between the black background, bright red roses, and decorative beads gives the table a luxurious appearance.

Tip: Use properly dried flowers suitable for resin casting. Moisture in fresh flowers can cause discoloration, bubbles, or other defects.

Step 5: Allow the First Layer to Cure

Once the floral arrangement is complete, leave the resin to cure for approximately 8–12 hours, as shown in the tutorial.

The actual curing time depends on the resin formulation and environmental conditions. Check the manufacturer's instructions before pouring the next layer.

Step 6: Pour the Second Layer of Resin

Prepare the second batch using:

  • 600 g epoxy resin

  • 300 g hardener

Mix both components thoroughly, scraping the sides and bottom of the container.

Carefully pour the mixture into the mould, ensuring that the floral arrangement is covered as intended.

Use a compatible bubble-removal spray only if permitted by the resin manufacturer. Allow the layer to cure according to the product instructions.

Step 7: Add the Third Layer of Resin

For the third layer, prepare another batch containing:

  • 600 g epoxy resin

  • 300 g hardener

Mix the ingredients thoroughly and pour the resin evenly into the mould.

Check the surface for bubbles and follow the recommended curing time before proceeding to the next layer.

Step 8: Pour the Fourth Layer of Resin

Prepare one more batch using:

  • 600 g epoxy resin

  • 300 g hardener

Pour the mixture into the mould to build up the required thickness of the table.

Remove bubbles using a method approved for the resin system, then allow the resin to cure fully before removing the table from the mould.

Always follow the resin manufacturer's maximum pouring-depth and temperature recommendations.

Step 9: Remove the Table from the Mould

After the resin has cured sufficiently, carefully remove the finished piece from the silicone mould.

Inspect the surface and edges. You may notice air bubbles or small imperfections that need to be corrected before applying the final coating.

Handle the piece carefully to avoid damaging the resin or decorative flowers.

Step 10: Sand the Resin Surface

The tutorial demonstrates sanding the surface with 40-grit sandpaper, followed by 80-grit sandpaper using a sanding machine.

Sand carefully to remove imperfections and prepare the surface for finishing. Coarse sandpaper removes material quickly, so avoid applying excessive pressure.

Wear suitable respiratory protection and use dust extraction while sanding. Make sure the resin is fully cured before beginning this process.

Step 11: Clean the Surface

After sanding, remove all dust from the table surface.

A clean surface is essential for achieving a smooth final coating. Check for any remaining holes, scratches, or imperfections before proceeding.

Step 12: Prepare the Final Resin Layer

For the final coating, measure:

  • 100 g epoxy resin

  • 50 g hardener

Mix thoroughly according to the manufacturer's specified ratio. Scrape the sides and bottom of the mixing container to ensure a consistent mixture.

Step 13: Apply the Final Glossy Coat

Pour the final resin mixture onto the surface of the table.

Spread it evenly to create a smooth, glossy finish. Remove bubbles using a suitable method approved by the resin manufacturer.

Fill small surface holes with compatible resin, ensuring that the coating remains even.

Allow the final layer to cure completely according to the manufacturer's instructions.

Step 14: Mark and Drill the Mounting Hole

Once the resin has fully cured, mark the centre or the required position for the table mounting hardware.

Carefully drill the hole using an appropriate drill bit and technique. Support the workpiece securely and take precautions to prevent cracking or damage.

Step 15: Attach the Table Base

Finally, install the mounting hardware and attach the table base.

The tutorial uses UV resin during the mounting process. However, the attachment method should be appropriate for the materials and the load the table will carry. Use a mechanically secure connection for a functional table.

Check that the base is stable and the mounting hardware is secure before using the table.

Congratulations! Your beautiful scarlet rose epoxy resin table is ready.

Important Tips for the Best Results

  • Always measure the resin and hardener accurately.

  • Follow the mixing ratio specified by the manufacturer.

  • Use dried flowers and clean decorative beads.

  • Mix slowly to minimize air bubbles.

  • Follow the recommended pouring depth for every layer.

  • Allow sufficient curing time between layers.

  • Use appropriate sanding equipment and remove all dust before applying the final coat.

  • Wear protective equipment and work in a well-ventilated area.

  • Ensure that the table base is securely attached before use.

Conclusion

Making an epoxy resin table with scarlet roses is a wonderful DIY project for anyone who enjoys creative crafts and home décor. The combination of black resin, vibrant red flowers, and decorative beads creates a distinctive design that looks elegant and artistic.

From preparing the mould and pouring the resin to arranging the flowers, sanding the surface, and applying the final glossy coat, every step contributes to the beauty of the finished table.

With patience, careful preparation, and the correct materials, you can create your own floral epoxy resin masterpiece.

Watch the video tutorial, follow the steps, and try making your own beautiful epoxy resin table!

Frequently Asked Questions

1. What size silicone mould is used for this project?

The project uses a 40 cm silicone mould.

2. How much resin is required?

The quantities listed in the tutorial total 2,800 g of resin and 1,400 g of hardener, or 4,200 g of combined mixture, excluding pigment. Actual requirements depend on the mould's depth, dimensions, and resin specifications.

3. Can fresh roses be used in epoxy resin?

Properly dried roses are generally more suitable because moisture in fresh flowers can cause defects or discoloration.

4. Why is sanding necessary?

Sanding helps remove surface imperfections and prepares the table for its final coating. The appropriate sanding sequence depends on the condition of the surface and the finish required.

5. How do you achieve a glossy finish?

A compatible final resin coating, applied to a clean and properly prepared surface, can create a glossy finish when allowed to cure according to the manufacturer's instructions.